YO8KSB-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO8KSB-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1753730531	13.35 Volt	30 Pkt	100 Pcnt
1753729629	13.35 Volt	30 Pkt	100 Pcnt
1753728729	13.35 Volt	30 Pkt	100 Pcnt
1753727828	13.35 Volt	30 Pkt	100 Pcnt
1753726927	13.35 Volt	30 Pkt	100 Pcnt
1753726026	13.35 Volt	40 Pkt	100 Pcnt
1753725125	13.35 Volt	40 Pkt	100 Pcnt
1753724224	13.35 Volt	40 Pkt	100 Pcnt
1753723323	13.35 Volt	40 Pkt	100 Pcnt
1753722453	13.35 Volt	40 Pkt	100 Pcnt
1753721522	13.35 Volt	40 Pkt	100 Pcnt
1753720621	13.35 Volt	40 Pkt	100 Pcnt
1753719720	13.35 Volt	40 Pkt	100 Pcnt
1753718819	13.35 Volt	40 Pkt	100 Pcnt
1753717918	13.35 Volt	40 Pkt	100 Pcnt
1753717017	13.35 Volt	40 Pkt	100 Pcnt
1753716116	13.35 Volt	40 Pkt	100 Pcnt
1753715215	13.35 Volt	40 Pkt	100 Pcnt
1753714314	13.35 Volt	40 Pkt	100 Pcnt
1753713414	13.35 Volt	40 Pkt	100 Pcnt
1753712513	13.35 Volt	40 Pkt	100 Pcnt
1753711612	13.35 Volt	40 Pkt	100 Pcnt
1753710711	13.35 Volt	40 Pkt	100 Pcnt
1753709810	13.35 Volt	40 Pkt	100 Pcnt
1753708909	13.35 Volt	30 Pkt	100 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)