KN4YDP-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KN4YDP-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1762638323	12.17 Volts	35.26 Deg.C
1762637782	12.17 Volts	36.24 Deg.C
1762637723	12.17 Volts	36.24 Deg.C
1762637711	12.17 Volts	36.24 Deg.C
1762637604	12.17 Volts	35.75 Deg.C
1762637422	12.17 Volts	35.75 Deg.C
1762637363	12.14 Volts	35.75 Deg.C
1762637244	12.17 Volts	35.75 Deg.C
1762637182	12.17 Volts	35.75 Deg.C
1762637123	12.17 Volts	35.26 Deg.C
1762636945	12.17 Volts	35.26 Deg.C
1762636524	12.17 Volts	35.26 Deg.C
1762631482	12.03 Volts	29.88 Deg.C
1762631362	12.03 Volts	29.88 Deg.C
1762631242	12 Volts	29.88 Deg.C
1762631182	12.03 Volts	29.39 Deg.C
1762631122	12.03 Volts	29.39 Deg.C
1762631062	12.03 Volts	29.39 Deg.C
1762630822	12 Volts	29.39 Deg.C
1762630702	12 Volts	28.9 Deg.C
1762630642	12 Volts	28.9 Deg.C
1762630522	12 Volts	28.9 Deg.C
1762630462	12 Volts	28.9 Deg.C
1762630383	12 Volts	28.41 Deg.C
1762630282	12 Volts	28.41 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.02933, 0

Temp: 0, 0.48876, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)