OE9XPT-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE9XPT-6. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1785299852	14.03 Volt	0 Pcnt	15.5 °c
1785299851	14.03 Volt	0 Pcnt	15.5 °c
1785299551	14.03 Volt	0 Pcnt	15 °c
1785299252	14.03 Volt	0 Pcnt	15 °c
1785299251	14.03 Volt	0 Pcnt	15 °c
1785298951	14.03 Volt	0 Pcnt	15 °c
1785298652	14.03 Volt	0 Pcnt	15 °c
1785298651	14.03 Volt	0 Pcnt	15 °c
1785298351	14.03 Volt	0 Pcnt	15 °c
1785298052	14.03 Volt	0 Pcnt	15 °c
1785298051	14.03 Volt	0 Pcnt	15 °c
1785297751	14.03 Volt	0 Pcnt	15.5 °c
1785297452	14.03 Volt	100 Pcnt	15.5 °c
1785297451	14.03 Volt	100 Pcnt	15.5 °c
1785297151	14.03 Volt	100 Pcnt	15.5 °c
1785296854	14.03 Volt	100 Pcnt	15.5 °c
1785296851	14.03 Volt	100 Pcnt	15.5 °c
1785296551	14.03 Volt	100 Pcnt	15.5 °c
1785296252	14.03 Volt	100 Pcnt	15.5 °c
1785296251	14.03 Volt	100 Pcnt	15.5 °c
1785295951	14.03 Volt	100 Pcnt	15.5 °c
1785295652	14.03 Volt	100 Pcnt	15.5 °c
1785295651	14.03 Volt	100 Pcnt	15.5 °c
1785295351	14.03 Volt	100 Pcnt	15 °c
1785295052	14.03 Volt	100 Pcnt	15 °c

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)