VK2RF-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2RF-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*
1777604619	13.92 Volts	39.32 Deg.C
1777604283	13.89 Volts	39.81 Deg.C
1777604170	13.83 Volts	39.81 Deg.C
1777603702	14.24 Volts	39.81 Deg.C
1777603603	13.95 Volts	39.81 Deg.C
1777603200	13.98 Volts	40.3 Deg.C
1777603100	14.3 Volts	40.3 Deg.C
1777603050	13.92 Volts	40.79 Deg.C
1777602970	13.89 Volts	40.79 Deg.C
1777602748	14.03 Volts	40.79 Deg.C
1777602699	13.89 Volts	40.79 Deg.C
1777602649	13.71 Volts	40.79 Deg.C
1777602556	13.86 Volts	41.28 Deg.C
1777602366	14.03 Volts	41.28 Deg.C
1777602340	14.06 Volts	40.79 Deg.C
1777602141	13.86 Volts	40.79 Deg.C
1777602092	13.89 Volts	41.28 Deg.C
1777601969	13.89 Volts	41.28 Deg.C
1777601866	13.92 Volts	41.28 Deg.C
1777601655	13.95 Volts	41.28 Deg.C
1777601505	14.09 Volts	41.28 Deg.C
1777601229	13.92 Volts	41.77 Deg.C
1777600895	13.89 Volts	41.28 Deg.C
1777600168	13.77 Volts	40.3 Deg.C
1777600031	13.8 Volts	38.83 Deg.C

*Used Equation Coefficients:

Value1: 0, 0.0293, 0

Value2: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)