SP9MOA-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP9MOA-6. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	T_in*	T_out*	Rx1h*	Dg1h*
1773189356	14.1 Volt	13.5 C	9 C	140 Pkt	10 Pkt
1773188759	14.1 Volt	14 C	9 C	130 Pkt	10 Pkt
1773188156	14 Volt	14 C	9 C	130 Pkt	10 Pkt
1773187558	14.1 Volt	14 C	9.5 C	130 Pkt	10 Pkt
1773186957	14 Volt	14 C	9.5 C	130 Pkt	10 Pkt
1773186357	14 Volt	14 C	9.5 C	120 Pkt	10 Pkt
1773185756	14 Volt	14 C	9.5 C	130 Pkt	10 Pkt
1773185156	14 Volt	14 C	9.5 C	130 Pkt	10 Pkt
1773184561	14 Volt	14.5 C	9.5 C	120 Pkt	0 Pkt
1773183957	14 Volt	14.5 C	10 C	120 Pkt	10 Pkt
1773183357	14 Volt	14 C	10 C	130 Pkt	10 Pkt
1773182760	14 Volt	14 C	10 C	130 Pkt	10 Pkt
1773182157	14 Volt	14 C	9.5 C	160 Pkt	10 Pkt
1773181559	14.1 Volt	14 C	9.5 C	190 Pkt	10 Pkt
1773180358	14.1 Volt	14 C	9.5 C	220 Pkt	10 Pkt
1773179158	14 Volt	14 C	10 C	210 Pkt	10 Pkt
1773178556	14 Volt	14 C	9.5 C	200 Pkt	10 Pkt
1773177956	14 Volt	14 C	9.5 C	170 Pkt	10 Pkt
1773177356	14 Volt	14 C	10 C	150 Pkt	10 Pkt
1773176756	14 Volt	14 C	10 C	150 Pkt	10 Pkt
1773176156	14 Volt	14 C	10 C	140 Pkt	10 Pkt
1773175560	14 Volt	14 C	10 C	140 Pkt	10 Pkt
1773174956	14 Volt	14 C	9.5 C	140 Pkt	10 Pkt
1773174360	14 Volt	14 C	10 C	140 Pkt	10 Pkt
1773173760	14 Volt	14 C	10 C	140 Pkt	10 Pkt

*Used Equation Coefficients:

Battery: 0, 0.1, 0

T_in: 0, 0.5, -64

T_out: 0, 0.5, -64

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)