IR1BY Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR1BY. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*	Temp*
1787570653	14.03 Volt	410 Pkt	95 Pcnt	27 C
1787570651	14.03 Volt	410 Pkt	95 Pcnt	27 C
1787568851	14.03 Volt	400 Pkt	91 Pcnt	26.5 C
1787568851	14.03 Volt	400 Pkt	91 Pcnt	26.5 C
1787567951	14.03 Volt	390 Pkt	89 Pcnt	25.5 C
1787567052	14.03 Volt	380 Pkt	85 Pcnt	25.5 C
1787567051	14.03 Volt	380 Pkt	85 Pcnt	25.5 C
1787566151	14.03 Volt	380 Pkt	83 Pcnt	25 C
1787565251	14.03 Volt	380 Pkt	82 Pcnt	24.5 C
1787564351	14.03 Volt	350 Pkt	80 Pcnt	24.5 C
1787563451	14.03 Volt	330 Pkt	79 Pcnt	23.5 C
1787562552	14.03 Volt	340 Pkt	79 Pcnt	23.5 C
1787561652	14.03 Volt	350 Pkt	80 Pcnt	23 C
1787561651	14.03 Volt	350 Pkt	80 Pcnt	23 C
1787559852	14.1 Volt	360 Pkt	79 Pcnt	22 C
1787559851	14.1 Volt	360 Pkt	79 Pcnt	22 C
1787558054	14.1 Volt	380 Pkt	79 Pcnt	21 C
1787558051	14.1 Volt	380 Pkt	79 Pcnt	21 C
1787556251	14.1 Volt	420 Pkt	81 Pcnt	20 C
1787554453	14.03 Volt	400 Pkt	78 Pcnt	19 C
1787554451	14.03 Volt	400 Pkt	78 Pcnt	19 C
1787552653	14.1 Volt	340 Pkt	80 Pcnt	18 C
1787552651	14.1 Volt	340 Pkt	80 Pcnt	18 C
1787551754	14.1 Volt	330 Pkt	85 Pcnt	18 C
1787550854	14.1 Volt	310 Pkt	90 Pcnt	17.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)