LY1BWB-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LY1BWB-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1772714496	14.1 Volt	0 Pkt	12 Pcnt
1772714495	14.1 Volt	0 Pkt	12 Pcnt
1772714195	14.1 Volt	10 Pkt	20 Pcnt
1772713895	14.1 Volt	10 Pkt	22 Pcnt
1772713601	14.1 Volt	10 Pkt	30 Pcnt
1772713296	14.1 Volt	10 Pkt	33 Pcnt
1772713295	14.1 Volt	10 Pkt	33 Pcnt
1772712995	14.1 Volt	10 Pkt	35 Pcnt
1772712695	14.1 Volt	10 Pkt	32 Pcnt
1772712395	14.1 Volt	10 Pkt	36 Pcnt
1772712096	14.1 Volt	10 Pkt	30 Pcnt
1772712095	14.1 Volt	10 Pkt	30 Pcnt
1772711795	14.1 Volt	10 Pkt	26 Pcnt
1772711495	14.1 Volt	10 Pkt	25 Pcnt
1772711195	14.1 Volt	10 Pkt	21 Pcnt
1772710896	14.1 Volt	0 Pkt	14 Pcnt
1772710895	14.1 Volt	0 Pkt	14 Pcnt
1772710607	14.1 Volt	10 Pkt	20 Pcnt
1772710295	14.1 Volt	10 Pkt	20 Pcnt
1772709995	14.1 Volt	10 Pkt	18 Pcnt
1772709696	14.1 Volt	10 Pkt	18 Pcnt
1772709695	14.1 Volt	10 Pkt	18 Pcnt
1772709395	14.1 Volt	10 Pkt	20 Pcnt
1772709095	14.1 Volt	10 Pkt	20 Pcnt
1772708795	14.1 Volt	10 Pkt	19 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)