BX4ACP-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX4ACP-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1765567267	25.4 C	15 p	46 p	1206 p
1765566067	24.9 C	16 p	44 p	1209 p
1765564866	24.8 C	15 p	41 p	1212 p
1765563666	25.6 C	13 p	39 p	1206 p
1765562466	25.1 C	13 p	39 p	1201 p
1765561266	25.1 C	13 p	41 p	1203 p
1765560066	24.5 C	13 p	37 p	1201 p
1765558866	25.2 C	15 p	38 p	1200 p
1765557666	25.9 C	9 p	34 p	1200 p
1765556466	25.1 C	14 p	30 p	1202 p
1765555266	25.8 C	11 p	21 p	1205 p
1765554066	26 C	5 p	14 p	1204 p
1765552866	26.5 C	5 p	14 p	1206 p
1765550466	28 C	5 p	17 p	1217 p
1765548066	27.5 C	6 p	24 p	1221 p
1765546867	27.1 C	10 p	26 p	1223 p
1765545667	28.1 C	8 p	42 p	1220 p
1765544467	28.2 C	8 p	43 p	1220 p
1765543266	27.5 C	26 p	45 p	1216 p
1765540866	27.9 C	10 p	19 p	1188 p
1765538467	28 C	4 p	14 p	1182 p
1765537266	27.7 C	4 p	20 p	1184 p
1765536067	28.2 C	6 p	22 p	1188 p
1765534867	27.7 C	10 p	29 p	1190 p
1765533667	27.4 C	6 p	76 p	1190 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)