WB5PJB-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WB5PJB-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1788478628	42.9 C	8.21 %	0 hPa
1788478324	42.9 C	13.38 %	0 hPa
1788477975	43 C	10.9 %	0 hPa
1788477535	43.6 C	8.23 %	0 hPa
1788477311	44.5 C	7.1 %	0 hPa
1788476918	45.6 C	9.56 %	818 hPa
1788463208	33 C	19.19 %	0 hPa
1788462949	33.3 C	16.83 %	824.5 hPa
1788460079	33.9 C	19.04 %	0 hPa
1788459320	31.9 C	19.25 %	0 hPa
1788459041	31.6 C	19.68 %	0 hPa
1788458799	30.7 C	20.66 %	823.13 hPa
1788442262	22.2 C	29.17 %	0 hPa
1788442066	22.3 C	28.44 %	0 hPa
1788441848	22.3 C	27.66 %	0 hPa
1788441556	22.7 C	27.73 %	0 hPa
1788441278	22.9 C	27.98 %	0 hPa
1788441057	23.2 C	28.63 %	0 hPa
1788440799	23.6 C	29.46 %	800.13 hPa
1788392206	28.9 C	32.14 %	0 hPa
1788392055	28.8 C	28.98 %	0 hPa
1788391904	28.6 C	32.01 %	0 hPa
1788391593	28.8 C	22.4 %	0 hPa
1788391190	29 C	25.84 %	0 hPa
1788390444	30.3 C	32.2 %	0 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)