ON0LGE-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ON0LGE-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1788568418	13.73 Volt	430 Pkt	180 Pkt	75 Pcnt
1788568156	14.03 Volt	430 Pkt	180 Pkt	75 Pcnt
1788568117	14.03 Volt	430 Pkt	180 Pkt	75 Pcnt
1788568117	14.03 Volt	430 Pkt	180 Pkt	75 Pcnt
1788567817	13.65 Volt	410 Pkt	180 Pkt	75 Pcnt
1788567517	13.73 Volt	410 Pkt	180 Pkt	77 Pcnt
1788567517	13.73 Volt	410 Pkt	180 Pkt	77 Pcnt
1788567217	14.03 Volt	410 Pkt	180 Pkt	78 Pcnt
1788566917	14.03 Volt	410 Pkt	180 Pkt	79 Pcnt
1788566917	14.03 Volt	410 Pkt	180 Pkt	79 Pcnt
1788566617	13.73 Volt	410 Pkt	180 Pkt	79 Pcnt
1788566317	14.03 Volt	410 Pkt	180 Pkt	79 Pcnt
1788566317	14.03 Volt	410 Pkt	180 Pkt	79 Pcnt
1788566016	14.03 Volt	420 Pkt	180 Pkt	78 Pcnt
1788565717	13.73 Volt	420 Pkt	180 Pkt	78 Pcnt
1788565717	13.73 Volt	420 Pkt	180 Pkt	78 Pcnt
1788565417	13.88 Volt	420 Pkt	180 Pkt	77 Pcnt
1788565165	14.03 Volt	410 Pkt	180 Pkt	77 Pcnt
1788565117	14.03 Volt	410 Pkt	180 Pkt	77 Pcnt
1788565117	14.03 Volt	410 Pkt	180 Pkt	77 Pcnt
1788564818	13.73 Volt	410 Pkt	180 Pkt	76 Pcnt
1788564517	14.03 Volt	410 Pkt	180 Pkt	76 Pcnt
1788564517	14.03 Volt	410 Pkt	180 Pkt	76 Pcnt
1788564217	14.03 Volt	420 Pkt	180 Pkt	76 Pcnt
1788563917	13.73 Volt	410 Pkt	190 Pkt	76 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)