NA7Q-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object NA7Q-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Solar*	Amps*	Watts*	Temp*
1761585549	13.51 V	19.07 V	5.53 A	75 W	44 F
1761584949	13.49 V	18.23 V	5.73 A	77 W	44 F
1761584348	13.44 V	18.04 V	4.06 A	55 W	43 F
1761583749	13.42 V	14.81 V	4.33 A	58 W	44 F
1761583149	13.44 V	18.7 V	4.66 A	63 W	43 F
1761582549	13.37 V	18.84 V	3.59 A	48 W	43 F
1761581949	13.34 V	19.5 V	2.59 A	35 W	43 F
1761581349	13.32 V	18.7 V	2.53 A	34 W	43 F
1761580749	13.29 V	18.65 V	2.33 A	31 W	43 F
1761580149	13.24 V	18.84 V	1.73 A	23 W	43 F
1761579549	13.22 V	20.29 V	0.46 A	6 W	43 F
1761578949	13.19 V	16.73 V	0.26 A	3 W	44 F
1761578349	13.19 V	17.48 V	0 A	0 W	44 F
1761577749	13.17 V	19.17 V	0 A	0 W	44 F
1761577149	13.17 V	14.67 V	0 A	0 W	44 F
1761576548	13.19 V	13.64 V	0 A	0 W	44 F
1761575949	13.15 V	12.14 V	0 A	0 W	44 F
1761575354	13.15 V	6.23 V	0 A	0 W	44 F
1761574749	13.15 V	0 V	0 A	0 W	44 F
1761574149	13.15 V	0 V	0 A	0 W	44 F
1761573549	13.15 V	0 V	0 A	0 W	44 F
1761572949	13.15 V	0 V	0 A	0 W	44 F
1761572350	13.15 V	0 V	0 A	0 W	44 F
1761571751	13.15 V	0 V	0 A	0 W	45 F
1761571149	13.15 V	0 V	0 A	0 W	45 F

*Used Equation Coefficients:

Battery: 0, 1, 0

Solar: 0, 1, 0

Amps: 0, 1, 0

Watts: 0, 1, 0

Temp: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)