W6UA Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W6UA. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1772664905	12.9 Volt	13 Pcnt	24 C
1772664005	12.9 Volt	13 Pcnt	24 C
1772663105	12.9 Volt	13 Pcnt	24.5 C
1772662205	12.9 Volt	13 Pcnt	24.5 C
1772661305	12.9 Volt	13 Pcnt	24.5 C
1772660405	12.9 Volt	13 Pcnt	24.5 C
1772660405	12.9 Volt	13 Pcnt	24.5 C
1772659505	12.9 Volt	13 Pcnt	24 C
1772658619	12.9 Volt	13 Pcnt	23.5 C
1772658619	12.9 Volt	13 Pcnt	23.5 C
1772657705	12.9 Volt	13 Pcnt	23 C
1772656805	12.9 Volt	13 Pcnt	23 C
1772656805	12.9 Volt	13 Pcnt	23 C
1772655905	12.9 Volt	13 Pcnt	22.5 C
1772655005	12.9 Volt	13 Pcnt	22 C
1772655005	12.9 Volt	13 Pcnt	22 C
1772654106	12.9 Volt	13 Pcnt	22 C
1772653206	12.9 Volt	13 Pcnt	21.5 C
1772653205	12.9 Volt	13 Pcnt	21.5 C
1772652306	12.9 Volt	13 Pcnt	21 C
1772651406	12.9 Volt	13 Pcnt	21 C
1772651405	12.9 Volt	13 Pcnt	21 C
1772649615	12.9 Volt	13 Pcnt	20 C
1772648706	12.9 Volt	13 Pcnt	19.5 C
1772647805	12.9 Volt	13 Pcnt	19 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)