LZ0DAP-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LZ0DAP-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin:*	Rx1h*	EffTo*	Temp*
1777082335	14.32 Volt	60 Pkt	88 Pcnt	25.14 C
1777081735	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777081135	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777080535	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777079935	14.32 Volt	60 Pkt	88 Pcnt	25.14 C
1777079335	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777078735	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777078135	14.32 Volt	60 Pkt	88 Pcnt	25.14 C
1777077535	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777076935	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777076335	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777075736	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777075136	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777074536	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777073936	14.32 Volt	80 Pkt	88 Pcnt	25.14 C
1777073336	14.32 Volt	80 Pkt	88 Pcnt	25.14 C
1777072736	14.32 Volt	80 Pkt	88 Pcnt	25.14 C
1777072136	14.32 Volt	80 Pkt	88 Pcnt	25.14 C
1777071536	14.32 Volt	80 Pkt	88 Pcnt	25.14 C
1777070936	14.32 Volt	80 Pkt	88 Pcnt	25.14 C
1777070336	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777069736	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777069136	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777068536	14.32 Volt	70 Pkt	88 Pcnt	25.14 C
1777067936	14.32 Volt	70 Pkt	88 Pcnt	25.14 C

*Used Equation Coefficients:

Vin:: 0, 0.077, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

EffTo: 0, 1, 0

Temp: 0, 0.147, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)