DC1MBB-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DC1MBB-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1776646529	24.3 deg C	49.1 %	1016.6 hPa
1776645624	24.2 deg C	49.4 %	1016.8 hPa
1776644722	24.2 deg C	49 %	1017.1 hPa
1776643822	24.3 deg C	48.9 %	1017.2 hPa
1776643502	24.3 deg C	48.8 %	1017.2 hPa
1776642597	24.3 deg C	49 %	1017.3 hPa
1776641699	24.3 deg C	49 %	1017.5 hPa
1776640793	24.3 deg C	49 %	1017.6 hPa
1776639897	24.3 deg C	49 %	1017.7 hPa
1776638994	24.4 deg C	48.9 %	1017.9 hPa
1776638084	24.3 deg C	49.1 %	1017.9 hPa
1776637188	24.3 deg C	49.2 %	1017.9 hPa
1776636291	24.3 deg C	49.2 %	1017.9 hPa
1776635392	24.3 deg C	49.1 %	1018 hPa
1776634496	24.3 deg C	49.1 %	1018 hPa
1776633591	24.3 deg C	49 %	1018 hPa
1776632686	24.5 deg C	48.5 %	1017.9 hPa
1776631791	24.5 deg C	48.8 %	1017.9 hPa
1776631791	24.5 deg C	48.8 %	1017.9 hPa
1776631478	24.5 deg C	48.8 %	1018 hPa
1776630578	24.5 deg C	48.9 %	1017.9 hPa
1776629676	24.5 deg C	49 %	1017.8 hPa
1776628776	24.5 deg C	49 %	1017.8 hPa
1776627876	24.6 deg C	49 %	1017.8 hPa
1776626972	24.6 deg C	49.2 %	1017.8 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)