OE3HOI-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3HOI-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Press*	Temp.in*	Temp.out*
1776628304	992.8 hPa	26.5 C deg	0 C deg
1776626505	992.7 hPa	26.6 C deg	0 C deg
1776622903	992.4 hPa	26.8 C deg	0 C deg
1776621103	992.4 hPa	27 C deg	0 C deg
1776619303	992.2 hPa	27.2 C deg	0 C deg
1776617503	992.2 hPa	27.5 C deg	0 C deg
1776613904	992.3 hPa	27.9 C deg	0 C deg
1776612102	992.7 hPa	28 C deg	0 C deg
1776610304	992.8 hPa	28 C deg	0 C deg
1776608502	993.1 hPa	28.1 C deg	0 C deg
1776606702	993.1 hPa	28.2 C deg	0 C deg
1776604910	993.4 hPa	28.2 C deg	0 C deg
1776603101	991.4 hPa	28.8 C deg	0 C deg
1776601301	991.2 hPa	29.3 C deg	0 C deg
1776599501	991.3 hPa	29.3 C deg	0 C deg
1776597701	991.8 hPa	29.4 C deg	0 C deg
1776590503	993.5 hPa	30.3 C deg	0 C deg
1776588701	993.8 hPa	32.1 C deg	0 C deg
1776586902	994.1 hPa	32.4 C deg	0 C deg
1776585111	994.2 hPa	32.2 C deg	0 C deg
1776583306	994.3 hPa	30 C deg	0 C deg
1776579712	994.4 hPa	28.2 C deg	0 C deg
1776577901	994.5 hPa	27.9 C deg	0 C deg
1776576100	994.7 hPa	26.4 C deg	0 C deg
1776574302	994.6 hPa	25.3 C deg	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)