SPRFLD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SPRFLD. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx1h*	Rx10m*	Temp*	Vin*
1784717049	470 Pkt	68 Pkt	83.5 F	13.48 Volt
1784716749	480 Pkt	62 Pkt	83.5 F	13.48 Volt
1784716449	490 Pkt	61 Pkt	83.5 F	13.48 Volt
1784716149	500 Pkt	102 Pkt	83.5 F	13.48 Volt
1784715849	490 Pkt	86 Pkt	83.5 F	13.48 Volt
1784715549	510 Pkt	70 Pkt	83.5 F	13.48 Volt
1784715249	510 Pkt	75 Pkt	83.5 F	13.48 Volt
1784714949	520 Pkt	67 Pkt	83.5 F	13.48 Volt
1784714649	520 Pkt	55 Pkt	83.5 F	13.48 Volt
1784714349	530 Pkt	94 Pkt	83.5 F	13.48 Volt
1784714049	530 Pkt	85 Pkt	83.5 F	13.48 Volt
1784713749	520 Pkt	63 Pkt	83.5 F	13.48 Volt
1784713449	530 Pkt	86 Pkt	83.5 F	13.48 Volt
1784713149	530 Pkt	83 Pkt	83.5 F	13.48 Volt
1784712849	520 Pkt	72 Pkt	83.5 F	13.48 Volt
1784712549	510 Pkt	111 Pkt	83.5 F	13.48 Volt
1784712249	490 Pkt	92 Pkt	83.5 F	13.48 Volt
1784711949	480 Pkt	77 Pkt	83.5 F	13.48 Volt
1784711649	470 Pkt	78 Pkt	83.5 F	13.48 Volt
1784711349	490 Pkt	75 Pkt	84.4 F	13.48 Volt
1784711049	500 Pkt	67 Pkt	84.4 F	13.48 Volt
1784710749	500 Pkt	86 Pkt	84.4 F	13.48 Volt
1784710449	500 Pkt	82 Pkt	84.4 F	13.48 Volt
1784710149	500 Pkt	73 Pkt	84.4 F	13.48 Volt
1784709849	500 Pkt	81 Pkt	84.4 F	13.48 Volt

*Used Equation Coefficients:

Rx1h: 0, 10, 0

Rx10m: 0, 1, 0

Dig1h: 0, 10, 0

Temp: 0, 0.9, -83

Vin: 0, 0.07, 0.53

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)