VK7DIK Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK7DIK. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1788610879	13.88 Volt	180 Pkt	98 Pcnt
1788610579	13.88 Volt	190 Pkt	98 Pcnt
1788610279	13.88 Volt	190 Pkt	99 Pcnt
1788609979	13.88 Volt	200 Pkt	99 Pcnt
1788609679	13.88 Volt	200 Pkt	99 Pcnt
1788609379	13.88 Volt	210 Pkt	98 Pcnt
1788609079	13.88 Volt	200 Pkt	98 Pcnt
1788608779	13.88 Volt	200 Pkt	98 Pcnt
1788608479	13.88 Volt	200 Pkt	97 Pcnt
1788608179	13.88 Volt	200 Pkt	97 Pcnt
1788607879	13.88 Volt	200 Pkt	98 Pcnt
1788607579	13.88 Volt	210 Pkt	98 Pcnt
1788607279	13.88 Volt	200 Pkt	98 Pcnt
1788606979	13.88 Volt	210 Pkt	97 Pcnt
1788606679	13.88 Volt	210 Pkt	97 Pcnt
1788606379	13.88 Volt	210 Pkt	97 Pcnt
1788606080	13.88 Volt	210 Pkt	97 Pcnt
1788605779	13.88 Volt	210 Pkt	97 Pcnt
1788605479	13.88 Volt	200 Pkt	98 Pcnt
1788605179	13.88 Volt	200 Pkt	96 Pcnt
1788604879	13.88 Volt	200 Pkt	96 Pcnt
1788604579	13.88 Volt	190 Pkt	96 Pcnt
1788604279	13.88 Volt	190 Pkt	96 Pcnt
1788603979	13.88 Volt	190 Pkt	95 Pcnt
1788603679	13.88 Volt	180 Pkt	95 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)