This is the latest recevied telemetry packets stored in our database for station/object IZ0JHY-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
TX*
RX*
Digi*
V_Bat*
V_Ext*
1780522633
0 Count
31 Count
0 Count
0 VDC
0 VDC
1780522033
0 Count
30 Count
0 Count
0 VDC
0 VDC
1780521628
0 Count
30 Count
0 Count
0 VDC
0 VDC
1780521028
0 Count
29 Count
0 Count
0 VDC
0 VDC
1780520913
0 Count
29 Count
0 Count
0 VDC
0 VDC
1780520312
0 Count
28 Count
0 Count
0 VDC
0 VDC
1780519712
0 Count
28 Count
0 Count
0 VDC
0 VDC
1780519112
0 Count
28 Count
0 Count
0 VDC
0 VDC
1780518512
0 Count
28 Count
0 Count
0 VDC
0 VDC
1780517912
0 Count
27 Count
0 Count
0 VDC
0 VDC
1780517312
0 Count
25 Count
0 Count
0 VDC
0 VDC
1780514071
0 Count
25 Count
0 Count
0 VDC
0 VDC
1780513471
0 Count
0 Count
0 Count
0 VDC
0 VDC
1780512670
0 Count
0 Count
0 Count
0 VDC
0 VDC
1780512596
0 Count
0 Count
0 Count
0 VDC
0 VDC
1780512175
0 Count
0 Count
0 Count
0 VDC
0 VDC
1780512141
0 Count
0 Count
0 Count
0 VDC
0 VDC
1780512136
0 Count
0 Count
0 Count
0 VDC
0 VDC
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)