DB0IS Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0IS. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BATT*	CPU*	CASE*	OUT*
1784696189	24.2 V	56.9 C	26 C	18.3 C
1784695589	24.1 V	57.4 C	26 C	18.3 C
1784694989	24.1 V	56.9 C	26 C	18.4 C
1784694388	24.2 V	56.9 C	25.5 C	18.5 C
1784693787	24.2 V	56.9 C	26 C	18.4 C
1784693187	24.1 V	57.4 C	26 C	18.4 C
1784692587	24.2 V	57.4 C	26 C	18.3 C
1784691986	24.2 V	57.4 C	26 C	18.3 C
1784691386	24.2 V	56.9 C	26 C	18.4 C
1784690785	24.2 V	56.9 C	25.5 C	18.4 C
1784690184	24.2 V	56.9 C	26 C	18.3 C
1784689583	24.2 V	56.9 C	26 C	18.4 C
1784688983	24.1 V	57.4 C	26 C	18.5 C
1784688382	24.1 V	56.9 C	26 C	18.5 C
1784687782	24.2 V	57.4 C	26 C	18.5 C
1784687181	24.2 V	56.9 C	26 C	18.5 C
1784686580	24.1 V	57.4 C	26 C	18.6 C
1784685979	24.1 V	57.9 C	26 C	18.6 C
1784685379	24.2 V	57.9 C	26 C	18.5 C
1784684778	24.1 V	56.9 C	26 C	18.6 C
1784684178	24.2 V	57.4 C	26 C	18.7 C
1784683578	24.2 V	57.9 C	26 C	18.7 C
1784682977	24.2 V	57.9 C	26 C	18.7 C
1784682377	24.1 V	56.9 C	26.5 C	18.7 C
1784681777	24.2 V	57.9 C	26.5 C	18.8 C

*Used Equation Coefficients:

BATT: 0, 0.1, 0

CPU: 0, 0.1, 0

CASE: 0, 0.1, 0

OUT: 0, 0.1, 0

PA: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)