N1DTA-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N1DTA-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1776681996	12.6 Volt	190 Pkt	98 Pcnt
1776681696	12.6 Volt	190 Pkt	94 Pcnt
1776681396	12.6 Volt	190 Pkt	91 Pcnt
1776681096	12.6 Volt	180 Pkt	89 Pcnt
1776680796	12.6 Volt	190 Pkt	87 Pcnt
1776680496	12.6 Volt	180 Pkt	84 Pcnt
1776680196	12.6 Volt	180 Pkt	85 Pcnt
1776679896	12.6 Volt	170 Pkt	84 Pcnt
1776679596	12.6 Volt	170 Pkt	85 Pcnt
1776679297	12.6 Volt	170 Pkt	85 Pcnt
1776678996	12.6 Volt	180 Pkt	85 Pcnt
1776678696	12.6 Volt	180 Pkt	85 Pcnt
1776678396	12.6 Volt	180 Pkt	86 Pcnt
1776678096	12.6 Volt	180 Pkt	90 Pcnt
1776677796	12.6 Volt	170 Pkt	92 Pcnt
1776677496	12.6 Volt	170 Pkt	95 Pcnt
1776677196	12.6 Volt	170 Pkt	97 Pcnt
1776676896	12.6 Volt	170 Pkt	99 Pcnt
1776676596	12.6 Volt	180 Pkt	99 Pcnt
1776676296	12.6 Volt	180 Pkt	96 Pcnt
1776675996	12.6 Volt	170 Pkt	95 Pcnt
1776675696	12.6 Volt	170 Pkt	93 Pcnt
1776675396	12.6 Volt	180 Pkt	93 Pcnt
1776675096	12.6 Volt	170 Pkt	93 Pcnt
1776674796	12.6 Volt	170 Pkt	92 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)