SP8QEO-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP8QEO-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1765578982	13.65 Volt	20 Pkt	58 Pcnt
1765578682	13.58 Volt	30 Pkt	58 Pcnt
1765578382	13.58 Volt	20 Pkt	56 Pcnt
1765578082	13.58 Volt	20 Pkt	62 Pcnt
1765577782	13.58 Volt	20 Pkt	58 Pcnt
1765577482	13.58 Volt	20 Pkt	57 Pcnt
1765577182	13.58 Volt	20 Pkt	60 Pcnt
1765576882	13.58 Volt	20 Pkt	58 Pcnt
1765576582	13.58 Volt	20 Pkt	56 Pcnt
1765576282	13.58 Volt	20 Pkt	55 Pcnt
1765575982	13.58 Volt	20 Pkt	57 Pcnt
1765575682	13.58 Volt	20 Pkt	54 Pcnt
1765575382	13.58 Volt	20 Pkt	55 Pcnt
1765575082	13.58 Volt	20 Pkt	53 Pcnt
1765574782	13.58 Volt	20 Pkt	54 Pcnt
1765574487	13.58 Volt	20 Pkt	51 Pcnt
1765574182	13.65 Volt	20 Pkt	56 Pcnt
1765573882	13.65 Volt	30 Pkt	58 Pcnt
1765573582	13.58 Volt	30 Pkt	59 Pcnt
1765573282	13.58 Volt	30 Pkt	66 Pcnt
1765572982	13.58 Volt	30 Pkt	67 Pcnt
1765572682	13.58 Volt	40 Pkt	71 Pcnt
1765572382	13.65 Volt	30 Pkt	71 Pcnt
1765572082	13.58 Volt	40 Pkt	76 Pcnt
1765571782	13.65 Volt	40 Pkt	79 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)