2E0ONV-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 2E0ONV-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Sate*	Temp*	Volt*	Alt*
1787668926	12	84.7 F	3.41 V	10 M
1787665916	12	85.1 F	3.52 V	10 M
1787662910	12	87.9 F	3.6 V	10 M
1787659903	12	85.2 F	3.65 V	0 M
1787657935	12	78.2 F	3.72 V	30 M
1787657307	12	76.1 F	3.61 V	40 M
1787654303	11	73.9 F	3.64 V	30 M
1787648284	12	70.5 F	3.66 V	30 M
1787645278	11	69.8 F	3.66 V	30 M
1787639347	11	69 F	3.68 V	20 M
1787597215	12	82 F	3.77 V	20 M
1787591194	5	89.2 F	3.77 V	30 M
1787588184	11	87.9 F	3.78 V	20 M
1787585171	12	87.8 F	3.79 V	10 M
1787582426	12	82 F	3.79 V	20 M
1787579420	11	80.2 F	3.8 V	50 M
1787576401	12	81.1 F	3.8 V	40 M
1787573381	12	87.8 F	3.81 V	20 M
1787570949	12	106.3 F	3.81 V	30 M
1787569914	9	91 F	3.86 V	10 M
1787569572	12	83.8 F	3.86 V	20 M
1787569248	12	78.6 F	3.88 V	10 M
1787565841	11	71.7 F	3.81 V	30 M
1787562830	8	69.8 F	3.82 V	60 M
1787559808	9	68.1 F	3.82 V	30 M

*Used Equation Coefficients:

Sate: 0, 1, 0

Temp: 0, 0.1, -50

Volt: 0, 0.01, 0

Alt: 0, 10, 0

A5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)