WCSAR-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WCSAR-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp*	U1*
1761579922	13.05 Volt	-5 C	12.7 Volt
1761579621	12.98 Volt	-5 C	12.6 Volt
1761578121	12.9 Volt	-5.5 C	12.6 Volt
1761577820	12.9 Volt	-5.5 C	12.6 Volt
1761577519	12.9 Volt	-5 C	12.6 Volt
1761577220	12.9 Volt	-5 C	12.6 Volt
1761576918	12.9 Volt	-5 C	12.6 Volt
1761576619	12.9 Volt	-5 C	12.6 Volt
1761527972	13.58 Volt	0 C	13.2 Volt
1761527371	13.65 Volt	0 C	13.3 Volt
1761526770	13.8 Volt	0 C	13.4 Volt
1761526470	13.88 Volt	0 C	13.5 Volt
1761526170	13.95 Volt	0 C	13.5 Volt
1761525870	14.1 Volt	0 C	13.7 Volt
1761525570	14.1 Volt	0 C	13.7 Volt
1761524069	14.1 Volt	0 C	13.7 Volt
1761521666	14.1 Volt	0.5 C	13.7 Volt
1761521366	14.1 Volt	0.5 C	13.7 Volt
1761521066	14.1 Volt	0.5 C	13.7 Volt
1761519264	14.1 Volt	0 C	13.7 Volt
1761517162	14.1 Volt	0 C	13.7 Volt
1761515661	14.1 Volt	0 C	13.7 Volt
1761514460	14.1 Volt	0 C	13.7 Volt
1761512358	14.1 Volt	-0.5 C	13.7 Volt
1761512057	14.1 Volt	-0.5 C	13.7 Volt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

U2: 0, 0.1, 0

Dg1h: 0, 10, 0

Temp: 0, 0.5, -64

U1: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)