XE2CT-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object XE2CT-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	TEMP*
1789956573	12.08 Volt	100 Pcnt	-64 C
1789956273	12.15 Volt	100 Pcnt	-64 C
1789955973	12.15 Volt	100 Pcnt	-64 C
1789955673	12.15 Volt	100 Pcnt	-64 C
1789955373	12.15 Volt	100 Pcnt	-64 C
1789955073	12.15 Volt	100 Pcnt	-64 C
1789954773	12.08 Volt	100 Pcnt	-64 C
1789954473	12.08 Volt	100 Pcnt	-64 C
1789954173	12.08 Volt	100 Pcnt	-64 C
1789953873	12.15 Volt	100 Pcnt	-64 C
1789953573	12.15 Volt	100 Pcnt	-64 C
1789953273	12.08 Volt	100 Pcnt	-64 C
1789952973	12.15 Volt	100 Pcnt	-64 C
1789952673	12.08 Volt	100 Pcnt	-64 C
1789952373	12.15 Volt	100 Pcnt	-64 C
1789952073	12.15 Volt	100 Pcnt	-64 C
1789951773	12.23 Volt	100 Pcnt	-64 C
1789951473	12.23 Volt	100 Pcnt	-64 C
1789951173	12.23 Volt	100 Pcnt	-64 C
1789950873	12.23 Volt	100 Pcnt	-64 C
1789950573	12.23 Volt	100 Pcnt	-64 C
1789950273	12.23 Volt	100 Pcnt	-64 C
1789949973	12.23 Volt	100 Pcnt	-64 C
1789949673	12.23 Volt	100 Pcnt	-64 C
1789949373	12.23 Volt	100 Pcnt	-64 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

TEMP: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)