DD2BU-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DD2BU-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Temp*	Humi*	Baro*
1762451077	21.5 deg C	50.1 %	1011.3 hPa
1762450177	21.6 deg C	49.9 %	1022.1 hPa
1762449277	21.6 deg C	49.7 %	1014.5 hPa
1762448377	21.7 deg C	49.6 %	1007.7 hPa
1762447477	21.7 deg C	49.4 %	1005.5 hPa
1762446577	21.8 deg C	49.3 %	1008.9 hPa
1762445677	21.7 deg C	49 %	1013.4 hPa
1762444777	22 deg C	48.9 %	1007.4 hPa
1762443876	21.9 deg C	49 %	1009.5 hPa
1762368389	21.8 deg C	51.1 %	1018.9 hPa
1762367489	21.6 deg C	51.1 %	1012 hPa
1762366589	21.6 deg C	51 %	1011.6 hPa
1762365689	21.6 deg C	50.9 %	1012.5 hPa
1762364788	21.6 deg C	50.8 %	1012.6 hPa
1762363888	21.6 deg C	50.8 %	1011.4 hPa
1762362988	21.6 deg C	50.8 %	1010.5 hPa
1762361188	21.7 deg C	51.5 %	1014 hPa
1762360288	21.6 deg C	51.5 %	1009.2 hPa
1762359388	21.5 deg C	50.8 %	1009.6 hPa
1762358488	21.3 deg C	49.9 %	1025.8 hPa
1762353087	22.5 deg C	48.7 %	1022.2 hPa
1762352187	22.7 deg C	48.5 %	1018.2 hPa
1762351287	22.7 deg C	48.5 %	1005 hPa
1762350387	22.6 deg C	48.5 %	1019 hPa
1762349487	22.7 deg C	48.3 %	1014.5 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)