ED1ZBK-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED1ZBK-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1761545704	14.03 Volt	100 Pcnt	-64 C
1761544804	14.03 Volt	100 Pcnt	-64 C
1761543904	14.03 Volt	100 Pcnt	-64 C
1761543004	14.03 Volt	100 Pcnt	-64 C
1761542104	14.03 Volt	100 Pcnt	-64 C
1761541204	14.03 Volt	100 Pcnt	-64 C
1761540305	14.03 Volt	100 Pcnt	-64 C
1761539405	14.03 Volt	100 Pcnt	-64 C
1761538505	14.03 Volt	100 Pcnt	-64 C
1761537605	14.03 Volt	100 Pcnt	-64 C
1761536705	14.03 Volt	100 Pcnt	-64 C
1761535805	14.03 Volt	100 Pcnt	-64 C
1761534905	14.03 Volt	100 Pcnt	-64 C
1761534005	14.03 Volt	100 Pcnt	-64 C
1761533105	14.03 Volt	100 Pcnt	-64 C
1761532205	14.03 Volt	100 Pcnt	-64 C
1761531305	14.03 Volt	100 Pcnt	-64 C
1761530405	14.03 Volt	100 Pcnt	-64 C
1761529505	14.03 Volt	100 Pcnt	-64 C
1761528605	14.03 Volt	100 Pcnt	-64 C
1761527705	14.03 Volt	100 Pcnt	-64 C
1761526805	14.03 Volt	100 Pcnt	-64 C
1761525905	14.03 Volt	100 Pcnt	-64 C
1761524105	14.03 Volt	100 Pcnt	-64 C
1761522305	14.03 Volt	100 Pcnt	-64 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)