HA8LLH-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HA8LLH-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Dg1h*	Eff1h*
1776696656	2.31 Volt	320 Pkt	10 Pcnt
1776696056	2.31 Volt	310 Pkt	9 Pcnt
1776695456	2.31 Volt	300 Pkt	10 Pcnt
1776694856	2.31 Volt	280 Pkt	9 Pcnt
1776694256	2.31 Volt	280 Pkt	10 Pcnt
1776693056	2.31 Volt	280 Pkt	11 Pcnt
1776692457	2.31 Volt	280 Pkt	11 Pcnt
1776691856	2.31 Volt	270 Pkt	11 Pcnt
1776691256	2.31 Volt	270 Pkt	10 Pcnt
1776690656	2.31 Volt	260 Pkt	10 Pcnt
1776690056	2.31 Volt	270 Pkt	10 Pcnt
1776689456	2.31 Volt	260 Pkt	9 Pcnt
1776688256	2.31 Volt	270 Pkt	10 Pcnt
1776687056	2.31 Volt	280 Pkt	11 Pcnt
1776685856	2.31 Volt	290 Pkt	11 Pcnt
1776685257	2.31 Volt	290 Pkt	11 Pcnt
1776684656	2.31 Volt	300 Pkt	12 Pcnt
1776683456	2.31 Volt	300 Pkt	12 Pcnt
1776682256	2.31 Volt	300 Pkt	13 Pcnt
1776681656	2.31 Volt	290 Pkt	13 Pcnt
1776681056	2.31 Volt	300 Pkt	13 Pcnt
1776680456	2.31 Volt	310 Pkt	13 Pcnt
1776679856	2.31 Volt	310 Pkt	13 Pcnt
1776679257	2.31 Volt	300 Pkt	12 Pcnt
1776678656	2.31 Volt	300 Pkt	12 Pcnt

*Used Equation Coefficients:

Temp: 0, 0.015, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)