W6SCR-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W6SCR-6. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	SARbatt*	Temp*	Rx1h*
1780558279	13.73 Volt	13.4 Volt	82.4 F	210 Pkt
1780557979	13.73 Volt	13.4 Volt	82.4 F	200 Pkt
1780557679	13.73 Volt	13.4 Volt	82.4 F	210 Pkt
1780557378	13.73 Volt	13.4 Volt	82.4 F	220 Pkt
1780557078	13.73 Volt	13.4 Volt	82.4 F	240 Pkt
1780556778	13.73 Volt	13.4 Volt	82.4 F	250 Pkt
1780556477	13.73 Volt	13.4 Volt	82.4 F	260 Pkt
1780556177	13.73 Volt	13.4 Volt	82.4 F	270 Pkt
1780555577	13.73 Volt	13.5 Volt	83.3 F	310 Pkt
1780555277	13.73 Volt	13.5 Volt	83.3 F	320 Pkt
1780554976	13.73 Volt	13.5 Volt	83.3 F	320 Pkt
1780554676	13.73 Volt	13.5 Volt	83.3 F	330 Pkt
1780554375	13.73 Volt	13.5 Volt	83.3 F	340 Pkt
1780554075	13.73 Volt	13.5 Volt	83.3 F	370 Pkt
1780553775	13.73 Volt	13.5 Volt	83.3 F	370 Pkt
1780553474	13.73 Volt	13.5 Volt	83.3 F	380 Pkt
1780553174	13.73 Volt	13.5 Volt	83.3 F	400 Pkt
1780552874	13.73 Volt	13.5 Volt	84.2 F	420 Pkt
1780552575	13.73 Volt	13.5 Volt	84.2 F	440 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

SARbatt: 0, 0.1, 0

SPIbat: 0, 0.1, 0

Temp: 0, 0.9, -83.2

Rx1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)