VK2RHR-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2RHR-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1788579276	14.03 Volt	80 Pkt	98 Pcnt
1788578676	14.03 Volt	80 Pkt	100 Pcnt
1788578076	14.03 Volt	70 Pkt	98 Pcnt
1788577476	14.03 Volt	70 Pkt	95 Pcnt
1788576876	14.03 Volt	80 Pkt	96 Pcnt
1788576276	14.03 Volt	70 Pkt	92 Pcnt
1788575679	14.03 Volt	60 Pkt	92 Pcnt
1788575076	14.03 Volt	80 Pkt	93 Pcnt
1788574476	14.03 Volt	80 Pkt	95 Pcnt
1788573876	14.03 Volt	80 Pkt	95 Pcnt
1788573277	14.03 Volt	70 Pkt	98 Pcnt
1788572676	14.03 Volt	80 Pkt	98 Pcnt
1788571477	14.03 Volt	70 Pkt	101 Pcnt
1788570877	14.03 Volt	60 Pkt	100 Pcnt
1788570276	14.03 Volt	60 Pkt	100 Pcnt
1788569676	14.03 Volt	50 Pkt	100 Pcnt
1788569081	14.03 Volt	40 Pkt	100 Pcnt
1788568476	14.03 Volt	40 Pkt	100 Pcnt
1788567878	14.03 Volt	40 Pkt	97 Pcnt
1788567277	14.03 Volt	50 Pkt	98 Pcnt
1788566677	14.03 Volt	50 Pkt	98 Pcnt
1788566077	14.03 Volt	50 Pkt	98 Pcnt
1788565477	14.03 Volt	50 Pkt	98 Pcnt
1788564877	14.03 Volt	50 Pkt	98 Pcnt
1788564277	14.03 Volt	50 Pkt	100 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)