IR5AO-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR5AO-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V_Ext*	Value2*	Value3*	Value4*	Value5*
1788349988	14.9 VDC	0	0	0	0
1788348039	14.94 VDC	0	0	0	0
1788346072	14.94 VDC	0	0	0	0
1788344104	14.96 VDC	0	0	0	0
1788342154	15.06 VDC	0	0	0	0
1788340199	15.06 VDC	0	0	0	0
1788338697	15.06 VDC	0	0	0	0
1788336473	15.04 VDC	0	0	0	0
1788334673	15.06 VDC	0	0	0	0
1788332873	15.06 VDC	0	0	0	0
1788331073	15.04 VDC	0	0	0	0
1788329272	14.14 VDC	0	0	0	0
1788327473	13.54 VDC	0	0	0	0
1788325673	12.66 VDC	0	0	0	0
1788323873	12.62 VDC	0	0	0	0
1788322073	12.62 VDC	0	0	0	0
1788320273	12.8 VDC	0	0	0	0
1788318473	12.76 VDC	0	0	0	0
1788316672	12.8 VDC	0	0	0	0
1788314872	12.84 VDC	0	0	0	0
1788313072	12.86 VDC	0	0	0	0
1788311272	12.58 VDC	0	0	0	0
1788309471	12.88 VDC	0	0	0	0
1788307670	12.8 VDC	0	0	0	0
1788305872	12.86 VDC	0	0	0	0

*Used Equation Coefficients:

V_Ext: 0, 0.02, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)