LY1BWB-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LY1BWB-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1784678835	13.73 Volt	20 Pkt	79 Pcnt
1784678535	13.73 Volt	10 Pkt	69 Pcnt
1784678535	13.73 Volt	10 Pkt	69 Pcnt
1784678235	13.73 Volt	20 Pkt	71 Pcnt
1784677939	13.73 Volt	20 Pkt	70 Pcnt
1784677635	13.73 Volt	20 Pkt	65 Pcnt
1784677335	13.73 Volt	20 Pkt	63 Pcnt
1784677035	13.73 Volt	20 Pkt	65 Pcnt
1784676735	13.73 Volt	20 Pkt	63 Pcnt
1784676435	13.73 Volt	20 Pkt	65 Pcnt
1784676135	13.73 Volt	20 Pkt	63 Pcnt
1784675835	13.73 Volt	20 Pkt	60 Pcnt
1784675535	13.73 Volt	20 Pkt	58 Pcnt
1784675235	13.73 Volt	20 Pkt	60 Pcnt
1784674935	13.73 Volt	10 Pkt	50 Pcnt
1784674935	13.73 Volt	10 Pkt	50 Pcnt
1784674635	13.73 Volt	20 Pkt	62 Pcnt
1784674335	13.73 Volt	20 Pkt	60 Pcnt
1784674035	13.73 Volt	20 Pkt	63 Pcnt
1784673735	13.73 Volt	20 Pkt	63 Pcnt
1784673435	13.73 Volt	20 Pkt	65 Pcnt
1784673135	13.73 Volt	20 Pkt	70 Pcnt
1784672835	13.73 Volt	20 Pkt	71 Pcnt
1784672535	13.73 Volt	20 Pkt	70 Pcnt
1784672235	13.73 Volt	20 Pkt	88 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)