2M0SBP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 2M0SBP-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	V Raw*	T-in*	T-out*
1773251390	12.38 Volt	13.4 Volt	19 C	13.5 C
1773251090	12.38 Volt	13.4 Volt	19 C	13.5 C
1773250790	12.3 Volt	13.4 Volt	19 C	14 C
1773250490	12.38 Volt	13.4 Volt	19.5 C	13.5 C
1773250190	12.38 Volt	13.4 Volt	19 C	14 C
1773249890	12.38 Volt	13.4 Volt	19.5 C	13.5 C
1773249590	12.38 Volt	13.4 Volt	19 C	14 C
1773249290	12.38 Volt	13.4 Volt	19.5 C	14 C
1773248990	12.3 Volt	13.4 Volt	19.5 C	14 C
1773248690	12.3 Volt	13.4 Volt	19 C	13.5 C
1773248390	12.38 Volt	13.4 Volt	19.5 C	14 C
1773248090	12.38 Volt	13.4 Volt	19.5 C	14 C
1773247790	12.3 Volt	13.4 Volt	19.5 C	14 C
1773247490	12.38 Volt	13.4 Volt	19.5 C	14 C
1773247190	12.38 Volt	13.4 Volt	19.5 C	14 C
1773246890	12.38 Volt	13.4 Volt	19.5 C	14 C
1773246590	12.38 Volt	13.4 Volt	19.5 C	14 C
1773246290	12.38 Volt	13.4 Volt	19.5 C	14 C
1773245990	12.38 Volt	13.4 Volt	19.5 C	14 C
1773245690	12.38 Volt	13.4 Volt	19.5 C	14 C
1773245390	12.38 Volt	13.4 Volt	19.5 C	14 C
1773245090	12.3 Volt	13.4 Volt	19.5 C	14 C
1773244790	12.38 Volt	13.4 Volt	19.5 C	14 C
1773244490	12.38 Volt	13.4 Volt	19.5 C	14 C
1773244190	12.3 Volt	13.4 Volt	19.5 C	14 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

V Raw: 0, 0.1, 0

DgR: 0, 0.001, 0

T-in: 0, 0.5, -64

T-out: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)