TA1FL Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA1FL. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1772705355	12.75 Volt	800 Pkt	78 Pcnt
1772705355	12.75 Volt	800 Pkt	78 Pcnt
1772705054	12.75 Volt	810 Pkt	78 Pcnt
1772704755	12.75 Volt	790 Pkt	77 Pcnt
1772704755	12.75 Volt	790 Pkt	77 Pcnt
1772704454	12.75 Volt	770 Pkt	77 Pcnt
1772704156	12.68 Volt	770 Pkt	76 Pcnt
1772704154	12.68 Volt	770 Pkt	76 Pcnt
1772703855	12.75 Volt	790 Pkt	77 Pcnt
1772703555	12.75 Volt	800 Pkt	77 Pcnt
1772703293	12.75 Volt	850 Pkt	79 Pcnt
1772703255	12.75 Volt	800 Pkt	77 Pcnt
1772703069	12.75 Volt	890 Pkt	80 Pcnt
1772702955	12.75 Volt	810 Pkt	77 Pcnt
1772702955	12.75 Volt	810 Pkt	77 Pcnt
1772702655	12.75 Volt	840 Pkt	77 Pcnt
1772702609	12.75 Volt	890 Pkt	79 Pcnt
1772702356	12.75 Volt	840 Pkt	78 Pcnt
1772702355	12.75 Volt	840 Pkt	78 Pcnt
1772702055	12.75 Volt	860 Pkt	79 Pcnt
1772701755	12.75 Volt	850 Pkt	79 Pcnt
1772701755	12.75 Volt	850 Pkt	79 Pcnt
1772701455	12.75 Volt	870 Pkt	79 Pcnt
1772701156	12.75 Volt	890 Pkt	80 Pcnt
1772701155	12.75 Volt	890 Pkt	80 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)