KD9GEE-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KD9GEE-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Battery*	Charging/AC*	GPS+Sat*
1781818234	99 Percent	48 Charge/On/Off	88 Sats/On/Off
1781817334	99 Percent	48 Charge/On/Off	83 Sats/On/Off
1781816434	99 Percent	48 Charge/On/Off	88 Sats/On/Off
1781815534	99 Percent	48 Charge/On/Off	88 Sats/On/Off
1781814633	99 Percent	48 Charge/On/Off	88 Sats/On/Off
1781813733	99 Percent	48 Charge/On/Off	95 Sats/On/Off
1781812833	99 Percent	48 Charge/On/Off	93 Sats/On/Off
1781811933	99 Percent	48 Charge/On/Off	88 Sats/On/Off
1781811033	99 Percent	48 Charge/On/Off	93 Sats/On/Off
1781810132	99 Percent	48 Charge/On/Off	93 Sats/On/Off
1781809232	99 Percent	48 Charge/On/Off	88 Sats/On/Off
1781808332	99 Percent	48 Charge/On/Off	88 Sats/On/Off
1781807800	99 Percent	48 Charge/On/Off	48 Sats/On/Off
1781807800	99 Percent	48 Charge/On/Off	88 Sats/On/Off
1781640319	99 Percent	48 Charge/On/Off	93 Sats/On/Off
1781639419	99 Percent	48 Charge/On/Off	93 Sats/On/Off
1781638519	99 Percent	48 Charge/On/Off	93 Sats/On/Off
1781637619	99 Percent	48 Charge/On/Off	83 Sats/On/Off
1781636718	99 Percent	48 Charge/On/Off	88 Sats/On/Off

*Used Equation Coefficients:

Battery: 0, 1, 0

Charging/AC: 0, 1, 0

GPS+Sat: 0, 1, 0

Current: 0, 10, -1280

A5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)