F5ZPO-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F5ZPO-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1784688727	13.13 Volt	210 Pkt	60 Pkt	66 Pcnt
1784688427	13.13 Volt	220 Pkt	60 Pkt	66 Pcnt
1784688127	13.13 Volt	220 Pkt	60 Pkt	67 Pcnt
1784687826	13.13 Volt	210 Pkt	60 Pkt	68 Pcnt
1784687526	13.13 Volt	200 Pkt	60 Pkt	68 Pcnt
1784687226	13.13 Volt	200 Pkt	60 Pkt	69 Pcnt
1784686925	13.13 Volt	210 Pkt	60 Pkt	70 Pcnt
1784686625	13.13 Volt	210 Pkt	60 Pkt	70 Pcnt
1784686325	13.13 Volt	210 Pkt	50 Pkt	70 Pcnt
1784686025	13.13 Volt	210 Pkt	50 Pkt	69 Pcnt
1784685724	13.13 Volt	210 Pkt	50 Pkt	69 Pcnt
1784685424	13.13 Volt	200 Pkt	50 Pkt	66 Pcnt
1784685124	13.13 Volt	190 Pkt	50 Pkt	65 Pcnt
1784684823	13.13 Volt	190 Pkt	50 Pkt	65 Pcnt
1784684524	13.13 Volt	190 Pkt	50 Pkt	61 Pcnt
1784684225	13.13 Volt	180 Pkt	50 Pkt	59 Pcnt
1784683923	13.13 Volt	180 Pkt	50 Pkt	59 Pcnt
1784683623	13.13 Volt	180 Pkt	50 Pkt	57 Pcnt
1784683322	13.13 Volt	180 Pkt	50 Pkt	56 Pcnt
1784683022	13.13 Volt	180 Pkt	50 Pkt	55 Pcnt
1784682722	12.9 Volt	180 Pkt	60 Pkt	55 Pcnt
1784682421	13.13 Volt	180 Pkt	60 Pkt	54 Pcnt
1784682121	13.13 Volt	190 Pkt	60 Pkt	53 Pcnt
1784681820	13.13 Volt	180 Pkt	60 Pkt	55 Pcnt
1784681522	13.13 Volt	190 Pkt	60 Pkt	55 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)