KB9WGP-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KB9WGP-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx1h*	Dg1h*	Eff1h*
1784796089	330 Pkt	80 Pkt	74 Pcnt
1784795789	320 Pkt	80 Pkt	72 Pcnt
1784795489	310 Pkt	80 Pkt	68 Pcnt
1784795189	310 Pkt	80 Pkt	68 Pcnt
1784794889	310 Pkt	80 Pkt	68 Pcnt
1784794589	310 Pkt	80 Pkt	68 Pcnt
1784794289	300 Pkt	80 Pkt	67 Pcnt
1784793989	290 Pkt	80 Pkt	67 Pcnt
1784793689	280 Pkt	80 Pkt	66 Pcnt
1784793389	280 Pkt	80 Pkt	66 Pcnt
1784793089	280 Pkt	80 Pkt	68 Pcnt
1784792789	290 Pkt	80 Pkt	67 Pcnt
1784792489	280 Pkt	80 Pkt	68 Pcnt
1784792189	290 Pkt	80 Pkt	70 Pcnt
1784791889	300 Pkt	80 Pkt	72 Pcnt
1784791589	290 Pkt	80 Pkt	71 Pcnt
1784791289	290 Pkt	80 Pkt	72 Pcnt
1784790989	290 Pkt	80 Pkt	72 Pcnt
1784790689	300 Pkt	90 Pkt	74 Pcnt
1784790389	290 Pkt	80 Pkt	74 Pcnt
1784790089	300 Pkt	80 Pkt	76 Pcnt
1784789789	300 Pkt	80 Pkt	77 Pcnt
1784789489	290 Pkt	80 Pkt	78 Pcnt
1784789189	290 Pkt	80 Pkt	79 Pcnt
1784788889	300 Pkt	90 Pkt	79 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)