KC2G Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC2G. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BatTemp*	Bat*	Solar*
1776682540	38.5 deg.F	13.3 V	15.9 V
1776681940	38.5 deg.F	13.3 V	16.15 V
1776681936	38.5 deg.F	13.3 V	15.45 V
1776681935	38.5 deg.F	13.25 V	15.4 V
1776681340	38.5 deg.F	13.3 V	14.9 V
1776681035	38.5 deg.F	13.3 V	15.5 V
1776680740	38.5 deg.F	13.3 V	15.35 V
1776680404	38.5 deg.F	13.25 V	15.1 V
1776680141	38.5 deg.F	13.25 V	14.75 V
1776680137	38.5 deg.F	13.25 V	15.1 V
1776680135	38.5 deg.F	13.25 V	15.15 V
1776679539	38.5 deg.F	13.2 V	13.15 V
1776679237	38.5 deg.F	13.2 V	13.1 V
1776679235	38.5 deg.F	13.2 V	13.1 V
1776678940	38.5 deg.F	13.2 V	11.7 V
1776678340	38.5 deg.F	13.2 V	10 V
1776678335	38.5 deg.F	13.2 V	10 V
1776677739	38.5 deg.F	13.2 V	10 V
1776677436	38.5 deg.F	13.2 V	10 V
1776677140	38.5 deg.F	13.2 V	10 V
1776676540	38.5 deg.F	13.2 V	10 V
1776676535	38.5 deg.F	13.2 V	10 V
1776675939	38.5 deg.F	13.2 V	10 V
1776675635	38.5 deg.F	13.2 V	10 V
1776675340	38.5 deg.F	13.2 V	10 V

*Used Equation Coefficients:

BatTemp: 0, 0.5, 0

Bat: 0, 0.05, 10

ChgA: 0, 0.05, 0

Solar: 0, 0.05, 10

Chg: 0.002, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)