This is the latest recevied telemetry packets stored in our database for station/object OK0BBK-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Avg 10m*
Avg 10m*
RxPkts*
IGateDropRx*
TxPkts*
1780547084
15.1 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780540645
15.1 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780534252
15.1 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780527856
15.2 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780521479
15.1 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780515077
15.1 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780508696
15.2 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780502252
15.2 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780495719
15.2 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780489287
15.2 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780482856
15.2 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780476364
15.2 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780469852
15.2 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780463404
15.2 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780456983
15.2 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
1780450613
15.2 Volt
15.8 Pkt
23.63 Pkt
-24.8 Pcnt
-64 None
*Used Equation Coefficients:
Avg 10m: 0, 0.1, 0
Avg 10m: 0, 0.1, 0
RxPkts: 0, 0.1953, -24.8031
IGateDropRx: 0, 0.1953, -24.8031
TxPkts: 0, 0.5, -64
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)