HG7RED-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HG7RED-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1789959475	12.83 Volt	340 Pkt	72 Pcnt
1789958276	12.83 Volt	330 Pkt	70 Pcnt
1789958275	12.83 Volt	330 Pkt	70 Pcnt
1789957076	12.83 Volt	350 Pkt	70 Pcnt
1789957075	12.83 Volt	350 Pkt	70 Pcnt
1789955876	12.83 Volt	320 Pkt	67 Pcnt
1789955875	12.83 Volt	320 Pkt	67 Pcnt
1789954676	12.83 Volt	310 Pkt	67 Pcnt
1789954675	12.83 Volt	310 Pkt	67 Pcnt
1789953476	12.83 Volt	290 Pkt	66 Pcnt
1789953475	12.83 Volt	290 Pkt	66 Pcnt
1789952276	12.83 Volt	300 Pkt	71 Pcnt
1789952275	12.83 Volt	300 Pkt	71 Pcnt
1789951076	12.83 Volt	290 Pkt	70 Pcnt
1789949876	12.83 Volt	300 Pkt	75 Pcnt
1789949876	12.83 Volt	300 Pkt	75 Pcnt
1789948676	12.83 Volt	310 Pkt	73 Pcnt
1789948676	12.83 Volt	310 Pkt	73 Pcnt
1789947476	12.83 Volt	340 Pkt	73 Pcnt
1789947476	12.83 Volt	340 Pkt	73 Pcnt
1789946276	12.83 Volt	330 Pkt	73 Pcnt
1789946276	12.83 Volt	330 Pkt	73 Pcnt
1789945076	12.83 Volt	350 Pkt	78 Pcnt
1789943876	12.83 Volt	340 Pkt	79 Pcnt
1789942676	12.83 Volt	340 Pkt	80 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)