EA2IP Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EA2IP. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vbat*	Temp*	Hum*	Press*
1789986985	3.66 V	31.5 C	48 %	1026 hPa
1789983805	3.72 V	28 C	49 %	1026 hPa
1789980625	3.78 V	26 C	49 %	1026 hPa
1789977445	3.82 V	25 C	49 %	1026 hPa
1789974264	3.88 V	26.5 C	47.5 %	1026 hPa
1789971084	3.94 V	24.5 C	50 %	1026 hPa
1789746260	4.08 V	29.5 C	38 %	1016 hPa
1789743070	0 V	31 C	36.5 %	1016 hPa
1789739890	0 V	31.5 C	36 %	1016 hPa
1789736711	0 V	30.5 C	37.5 %	1016 hPa
1789733531	0 V	31.5 C	37.5 %	1016 hPa
1789730351	0 V	29.5 C	39 %	1016 hPa
1789727172	0 V	30.5 C	38 %	1016 hPa
1789723992	0 V	29 C	39 %	1016 hPa
1789720812	0 V	28 C	39.5 %	1016 hPa
1789717631	0 V	31.5 C	35 %	1015 hPa
1789714461	3.72 V	21 C	56 %	1015 hPa
1789615644	3.6 V	28 C	40 %	1017 hPa
1789612465	3.64 V	28 C	40.5 %	1017 hPa
1789609285	3.68 V	28.5 C	39.5 %	1017 hPa
1789606105	3.74 V	28.5 C	40 %	1018 hPa
1789602925	3.8 V	29 C	40 %	1018 hPa
1789599745	3.86 V	29 C	39 %	1019 hPa
1789596565	3.9 V	29.5 C	38.5 %	1019 hPa
1789593394	3.94 V	30 C	37 %	1019 hPa

*Used Equation Coefficients:

Vbat: 0, 0.02, 0

I: 0, 10, -1280

Temp: 0, 0.5, -20

Hum: 0, 0.5, 0

Press: 0, 1, 880

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)