DO7BTR-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DO7BTR-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1781674210	12.2 deg C	84.4 %	1015.5 hPa
1781673306	11.9 deg C	85.2 %	1015.6 hPa
1781672402	11.6 deg C	86.5 %	1015.6 hPa
1781671502	10.9 deg C	86.4 %	1015.4 hPa
1781586526	10.2 deg C	83.1 %	1012.7 hPa
1781585630	9.8 deg C	83.4 %	1012.6 hPa
1781500718	14.2 deg C	83.4 %	1010.2 hPa
1781499817	13.8 deg C	84.8 %	1010.2 hPa
1781498909	13 deg C	88.4 %	1010.1 hPa
1781454693	16 deg C	75.5 %	1012.1 hPa
1781453790	15.9 deg C	77.2 %	1012.1 hPa
1781452886	15.9 deg C	76.8 %	1012.2 hPa
1781451986	15.9 deg C	76.9 %	1012.2 hPa
1781451086	15.9 deg C	77.9 %	1012.2 hPa
1781450183	16.5 deg C	76 %	1012.2 hPa
1781449281	17 deg C	73.6 %	1012.2 hPa
1781448381	17.4 deg C	73.6 %	1012.1 hPa
1781447482	17.4 deg C	73.6 %	1012.1 hPa
1781446582	17.1 deg C	72.9 %	1012.1 hPa
1781445679	17.3 deg C	75 %	1012.1 hPa
1781444774	17.2 deg C	74.9 %	1012.1 hPa
1781443866	16.9 deg C	75.4 %	1012 hPa
1781442965	16.7 deg C	76 %	1011.9 hPa
1781442068	16.6 deg C	75.9 %	1011.8 hPa
1781441171	16.8 deg C	75.7 %	1011.8 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)