VE3GUK-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VE3GUK-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1772860084	13.8 Volt	100 Pcnt	9.5 C
1772859484	13.8 Volt	100 Pcnt	9.5 C
1772858884	13.8 Volt	83 Pcnt	9 C
1772858284	13.8 Volt	83 Pcnt	9 C
1772857684	13.8 Volt	83 Pcnt	9 C
1772857084	13.8 Volt	83 Pcnt	9 C
1772856484	13.8 Volt	83 Pcnt	9 C
1772855884	13.8 Volt	83 Pcnt	8.5 C
1772855284	13.8 Volt	100 Pcnt	8.5 C
1772854684	13.8 Volt	100 Pcnt	8 C
1772854084	13.8 Volt	100 Pcnt	8 C
1772853484	13.8 Volt	100 Pcnt	8 C
1772852884	13.8 Volt	100 Pcnt	8 C
1772852284	13.8 Volt	100 Pcnt	8 C
1772851684	13.8 Volt	100 Pcnt	8 C
1772851084	13.8 Volt	100 Pcnt	8 C
1772850484	13.8 Volt	100 Pcnt	7.5 C
1772849884	13.8 Volt	100 Pcnt	7.5 C
1772849284	13.8 Volt	100 Pcnt	7.5 C
1772848684	13.8 Volt	100 Pcnt	7.5 C
1772848084	13.8 Volt	100 Pcnt	7.5 C
1772847484	13.8 Volt	100 Pcnt	7.5 C
1772846884	13.8 Volt	100 Pcnt	7.5 C
1772846284	13.8 Volt	100 Pcnt	7.5 C
1772845684	13.8 Volt	100 Pcnt	7.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)