DB3LO-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB3LO-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Temp*	Humi*	Value3*	Value4*	Value5*
1780574779	27.8 deg C	0 %	0	0	0
1780573883	30.5 deg C	34.6 %	0	0	0
1780572988	30.2 deg C	35.9 %	0	0	0
1780572085	30.7 deg C	33.4 %	0	0	0
1780569377	27.5 deg C	38.6 %	0	0	0
1780567585	26.6 deg C	44 %	0	0	0
1780566687	22.1 deg C	50.2 %	0	0	0
1780564891	19.7 deg C	55.1 %	0	0	0
1780402588	24.9 deg C	49.3 %	0	0	0
1780401693	27.7 deg C	55.9 %	0	0	0
1780400790	26.9 deg C	48.2 %	0	0	0
1780399894	33.8 deg C	39.1 %	0	0	0
1780398991	35 deg C	41.9 %	0	0	0
1780398088	32.5 deg C	41.2 %	0	0	0
1780397189	31.3 deg C	38.1 %	0	0	0
1780396282	28 deg C	44.2 %	0	0	0
1780395383	24.5 deg C	53.6 %	0	0	0
1780394487	22.2 deg C	52.7 %	0	0	0
1780393592	23.4 deg C	56.9 %	0	0	0
1780393592	-	-	-	-	-
1780392697	23.1 deg C	48.6 %	0	0	0
1780391792	24 deg C	50.3 %	0	0	0
1780390888	22.6 deg C	56.7 %	0	0	0
1780389985	20.2 deg C	61.9 %	0	0	0
1780232130	31.7 deg C	31.5 %	0	0	0

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)