SR4PA Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR4PA. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*
1766370935	14.03 Volt	1330 Pkt	1280 Pkt
1766370934	14.03 Volt	1330 Pkt	1280 Pkt
1766370634	14.03 Volt	1330 Pkt	1280 Pkt
1766370034	14.03 Volt	1330 Pkt	1280 Pkt
1766369735	14.03 Volt	1330 Pkt	1280 Pkt
1766369734	14.03 Volt	1330 Pkt	1280 Pkt
1766369434	14.03 Volt	1330 Pkt	1280 Pkt
1766369135	14.03 Volt	1340 Pkt	1280 Pkt
1766369134	14.03 Volt	1340 Pkt	1280 Pkt
1766368535	14.03 Volt	1330 Pkt	1280 Pkt
1766368534	14.03 Volt	1330 Pkt	1280 Pkt
1766368234	14.03 Volt	1330 Pkt	1280 Pkt
1766367937	14.03 Volt	1330 Pkt	1280 Pkt
1766367934	14.03 Volt	1330 Pkt	1280 Pkt
1766367335	14.03 Volt	1340 Pkt	1280 Pkt
1766367334	14.03 Volt	1340 Pkt	1280 Pkt
1766367034	14.03 Volt	1330 Pkt	1280 Pkt
1766366736	14.03 Volt	1330 Pkt	1280 Pkt
1766366734	14.03 Volt	1330 Pkt	1280 Pkt
1766366434	14.03 Volt	1330 Pkt	1280 Pkt
1766366136	14.03 Volt	1330 Pkt	1280 Pkt
1766366134	14.03 Volt	1330 Pkt	1280 Pkt
1766365835	14.03 Volt	1330 Pkt	1280 Pkt
1766365535	14.03 Volt	1330 Pkt	1280 Pkt
1766365534	14.03 Volt	1330 Pkt	1280 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)