IW3BRC-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IW3BRC-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Druck*	Wind*
1781403852	12.9 degC	1017 hPa	0.4 m/s
1781400131	14.1 degC	1017 hPa	0.6 m/s
1781396409	15.5 degC	1017 hPa	0.4 m/s
1781392690	16.1 degC	1017 hPa	1.2 m/s
1781388969	16.9 degC	1017 hPa	0.7 m/s
1781385248	17.9 degC	1016 hPa	0.8 m/s
1781381526	19.4 degC	1015 hPa	0.1 m/s
1781377806	22.7 degC	1014 hPa	1.5 m/s
1781374085	26.2 degC	1013 hPa	0.9 m/s
1781370362	29.3 degC	1012 hPa	1.1 m/s
1781366641	30.5 degC	1012 hPa	1.6 m/s
1781362918	30.6 degC	1013 hPa	2.1 m/s
1781359199	29.8 degC	1014 hPa	2 m/s
1781355477	29 degC	1015 hPa	1.2 m/s
1781351757	27.6 degC	1017 hPa	0.9 m/s
1781348033	25.9 degC	1018 hPa	1.2 m/s
1781344312	24.3 degC	1019 hPa	0.4 m/s
1781340589	22.4 degC	1020 hPa	0.9 m/s
1781336869	20.2 degC	1021 hPa	0.2 m/s
1781333148	18.8 degC	1022 hPa	0.5 m/s
1781329425	16.4 degC	1022 hPa	0.4 m/s
1781325704	15.1 degC	1022 hPa	0.2 m/s
1781321984	14.2 degC	1022 hPa	0.1 m/s
1781318264	14.4 degC	1022 hPa	0 m/s
1781314542	14.1 degC	1022 hPa	0.2 m/s

*Used Equation Coefficients:

Temp: 0, 0.1, -50

Druck: 0, 1, 800

Wind: 0, 0.1, 0

Regen: 0, 1, 0

Wasser: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)