KELLER Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KELLER. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1765590261	14.03 Volt	630 Pkt	130 Pkt	79 Pcnt
1765588461	14.03 Volt	650 Pkt	150 Pkt	82 Pcnt
1765586661	14.03 Volt	610 Pkt	120 Pkt	86 Pcnt
1765584861	14.03 Volt	510 Pkt	100 Pkt	86 Pcnt
1765583061	14.03 Volt	430 Pkt	90 Pkt	85 Pcnt
1765581261	14.03 Volt	460 Pkt	90 Pkt	85 Pcnt
1765579461	14.03 Volt	440 Pkt	80 Pkt	76 Pcnt
1765577661	14.03 Volt	510 Pkt	90 Pkt	79 Pcnt
1765575861	14.03 Volt	530 Pkt	80 Pkt	88 Pcnt
1765574061	14.03 Volt	470 Pkt	80 Pkt	88 Pcnt
1765572261	13.95 Volt	460 Pkt	100 Pkt	87 Pcnt
1765570461	14.03 Volt	430 Pkt	120 Pkt	87 Pcnt
1765568661	14.03 Volt	440 Pkt	120 Pkt	86 Pcnt
1765566861	14.03 Volt	530 Pkt	130 Pkt	86 Pcnt
1765565061	14.03 Volt	550 Pkt	100 Pkt	88 Pcnt
1765563261	14.03 Volt	540 Pkt	80 Pkt	87 Pcnt
1765561461	14.03 Volt	510 Pkt	100 Pkt	84 Pcnt
1765559661	14.03 Volt	490 Pkt	90 Pkt	86 Pcnt
1765557862	13.73 Volt	510 Pkt	70 Pkt	88 Pcnt
1765556062	13.73 Volt	470 Pkt	70 Pkt	89 Pcnt
1765554262	14.03 Volt	440 Pkt	80 Pkt	89 Pcnt
1765552462	14.03 Volt	420 Pkt	80 Pkt	86 Pcnt
1765548862	14.03 Volt	400 Pkt	70 Pkt	91 Pcnt
1765547062	14.03 Volt	370 Pkt	70 Pkt	90 Pcnt
1765545262	14.03 Volt	380 Pkt	70 Pkt	90 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)