DL1MBW-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL1MBW-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Sate*	Temp*	Volt*	Alt*
1761491000	12	19.5 C	3.66 V	500 M
1761490840	12	19.6 C	3.67 V	510 M
1761490679	12	19.5 C	3.67 V	510 M
1761490519	12	19.5 C	3.67 V	510 M
1761490359	12	19.5 C	3.67 V	510 M
1761490039	12	19.1 C	3.67 V	510 M
1761489879	12	18.8 C	3.66 V	500 M
1761489559	12	18.1 C	3.7 V	500 M
1761489369	12	17.1 C	3.85 V	540 M
1761489049	11	15.6 C	3.85 V	540 M
1761485917	11	17.5 C	3.66 V	540 M
1761485277	12	16.8 C	3.66 V	550 M
1761485117	12	16.5 C	3.67 V	550 M
1761417850	11	21.4 C	3.67 V	500 M
1761417691	12	21.7 C	3.65 V	510 M
1761417530	11	22 C	3.65 V	500 M
1761417209	12	22.5 C	3.67 V	500 M
1761416569	12	23.1 C	3.7 V	500 M
1761416409	12	23.1 C	3.81 V	500 M
1761416249	10	22.6 C	3.81 V	500 M
1761416089	9	21.6 C	3.82 V	500 M
1761415894	10	21.1 C	3.82 V	520 M
1761415734	7	20.7 C	3.81 V	540 M
1761415415	11	19.5 C	3.82 V	520 M
1761415254	11	18.8 C	3.83 V	540 M

*Used Equation Coefficients:

Sate: 0, 1, 0

Temp: 0, 0.1, -50

Volt: 0, 0.01, 0

Alt: 0, 10, 0

A5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)