OK4JL-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OK4JL-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1787422283	30.4 C	37.89 %	1023.25 hPa
1787422068	30.2 C	38.45 %	1023 hPa
1787421801	29.9 C	39.3 %	1017.5 hPa
1787420897	28.4 C	42.52 %	1022.88 hPa
1787420720	28 C	43.05 %	1023.13 hPa
1787420565	27.5 C	44.59 %	1017.63 hPa
1787420416	27.1 C	44.73 %	1015 hPa
1787420265	26.4 C	45.68 %	1015.38 hPa
1787420065	25.7 C	47.12 %	1016.75 hPa
1787420020	25.7 C	47.12 %	1014.38 hPa
1787419964	25.4 C	47 %	983.75 hPa
1787386314	14.2 C	61.45 %	1017.88 hPa
1787385409	14.2 C	62.04 %	1015.38 hPa
1787384505	13.6 C	62.64 %	1017 hPa
1787383601	13.2 C	63.97 %	1014.13 hPa
1787382470	11.5 C	66.01 %	1007.63 hPa
1787382023	10.6 C	66.65 %	984.5 hPa
1787304358	24.2 C	48.26 %	1008.38 hPa
1787303453	23.8 C	47.33 %	1011.25 hPa
1787302550	24.7 C	44.87 %	1010.88 hPa
1787301646	27.4 C	42.63 %	1012.63 hPa
1787300742	29.6 C	40.31 %	1012.75 hPa
1787299838	33 C	38.55 %	1012.38 hPa
1787298941	32.7 C	43.74 %	1012.5 hPa
1787298037	25.2 C	50.25 %	981 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)