VK2GJ-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2GJ-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vbat*	Psys*	Temp*	AirP*
1787676950	3.27 V	64 mW	23.8 degC	500 Pa
1787676759	3.27 V	64 mW	23.9 degC	500 Pa
1787675150	3.27 V	64 mW	24.5 degC	500 Pa
1787675049	3.27 V	64 mW	24.2 degC	500 Pa
1787674959	3.27 V	64 mW	24.3 degC	500 Pa
1787673350	3.27 V	64 mW	24.6 degC	500 Pa
1787673159	3.27 V	64 mW	24.5 degC	500 Pa
1787671553	3.27 V	64 mW	25.2 degC	500 Pa
1787671452	3.27 V	64 mW	25.2 degC	500 Pa
1787671358	3.27 V	64 mW	25.2 degC	500 Pa
1787669749	3.27 V	64 mW	25.2 degC	500 Pa
1787669559	3.27 V	64 mW	25.3 degC	500 Pa
1787667949	3.27 V	64 mW	25.2 degC	500 Pa
1787667836	3.27 V	64 mW	25.1 degC	500 Pa
1787667758	3.27 V	64 mW	25.1 degC	500 Pa
1787666157	3.27 V	64 mW	25.7 degC	500 Pa
1787665958	3.27 V	64 mW	25.4 degC	500 Pa
1787664237	3.27 V	64 mW	25.4 degC	500 Pa
1787664158	3.27 V	64 mW	25.5 degC	500 Pa
1787662545	3.27 V	64 mW	25.9 degC	500 Pa
1787662358	3.27 V	64 mW	25.7 degC	500 Pa
1787660745	3.27 V	64 mW	25.7 degC	500 Pa
1787660637	3.27 V	64 mW	25.1 degC	500 Pa
1787660558	3.27 V	64 mW	25.6 degC	500 Pa
1787658945	3.27 V	64 mW	25.7 degC	500 Pa

*Used Equation Coefficients:

Vbat: 0, 0.001, 0

Vsol: 0, 0.001, 0

Psys: 0, 2, 0

Temp: 0, 0.1, -100

AirP: 0, 12.5, 500

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)