OATMAN Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OATMAN. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1780893925	12.9 Volt	100 Pcnt	36 C
1780893625	12.9 Volt	100 Pcnt	36 C
1780893324	12.9 Volt	100 Pcnt	36 C
1780893024	12.9 Volt	100 Pcnt	36.5 C
1780892724	12.9 Volt	100 Pcnt	36.5 C
1780892423	12.9 Volt	100 Pcnt	36.5 C
1780892123	12.9 Volt	100 Pcnt	36.5 C
1780891823	12.9 Volt	100 Pcnt	36.5 C
1780891523	12.9 Volt	100 Pcnt	36.5 C
1780891222	12.9 Volt	100 Pcnt	36.5 C
1780890923	12.9 Volt	100 Pcnt	36.5 C
1780890622	12.9 Volt	100 Pcnt	36.5 C
1780890322	12.9 Volt	100 Pcnt	36.5 C
1780890021	12.9 Volt	100 Pcnt	37 C
1780889721	12.9 Volt	100 Pcnt	37 C
1780889421	12.9 Volt	100 Pcnt	37 C
1780889120	12.9 Volt	100 Pcnt	37 C
1780888820	12.9 Volt	100 Pcnt	37 C
1780888520	12.9 Volt	100 Pcnt	37 C
1780888220	12.9 Volt	100 Pcnt	37 C
1780887921	12.9 Volt	100 Pcnt	37 C
1780887620	12.9 Volt	100 Pcnt	37 C
1780887319	12.9 Volt	100 Pcnt	37 C
1780887018	12.98 Volt	100 Pcnt	37 C
1780886718	12.98 Volt	100 Pcnt	37 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)